The fundamental skill for developing a machine is learned by carrying out technical calculation, drawing an assembly diagram
and drawing parts diagrams
The capability for designing a mechanical machine which consists of two or more parts is learned based on the knowledge mastered
by classes of mechanical material, mechanism, processing technology, general dynamics, etc.. The capability to draw a mechanical
machine is learned based on the rule of engineering drawing.
- Getting a capability for performing the design of a machine, considering mechanical material, mechanism, material mechanics, processing technology and so on.
- Getting a capability for drawing an assembly diagram based on the rule of JIS engineering drawing.
- Getting a capability for drawing an parts diagram based on geometric tolerance, a maximum material principle, the directions method of surface quality, etc.
| Class schedule | HW assignments (Including preparation and review of the class.) | Amount of Time Required | |
|---|---|---|---|
| 1. | Explanation of task. Study of gears. Module calculation. Dimension calculation of gear. Preparation of study chart. Strength calculation of driving parts. Selection of bearings. Study on casing method and lubrication method. Create a design document. | Students make technical calculations and create reports. | 200minutes |
| 2. | Layout consideration (whole). | Layout consideration (whole). | 200minutes |
| 3. | Layout consideration (details). | Layout consideration (details). | 200minutes |
| 4. | Drawing of assembly drawing (front view) | Drawing of assembly drawing (front view) | 200minutes |
| 5. | Drawing of assembly drawing (plan view) and assembly drawing (side view) | Drawing of assembly drawing (plan view) and assembly drawing (side view) | 200minutes |
| 6. | Evaluation of assembly drawing, instructions for re-submission etc. | Drawing of assembly drawing (plan view) and assembly drawing (side view) | 200minutes |
| 7. | Drafting of a part diagram (casing) | Drafting of a part diagram (casing) | 200minutes |
| 8. | Evaluation of a part diagram (casing), directions of re-presentation, etc. | Drafting of a part diagram (casing) | 200minutes |
| 9. | Drafting of a part diagram (shaft) | Drafting of a part diagram (shaft) | 200minutes |
| 10. | Evaluation of a part diagram (shaft), directions of re-presentation, etc. | Drafting of a part diagram (shaft) | 200minutes |
| 11. | Drafting of a part diagram (gears) | Drafting of a part diagram (gears) | 200minutes |
| 12. | Evaluation of a part diagram (gears), directions of re-presentation, etc. | Drafting of a part diagram (gears) | 200minutes |
| 13. | Drafting of a part diagram (lids and so on). | Drafting of a part diagram (lids and so on). | 200minutes |
| 14. | Evaluation of a part diagram (lids and so on), directions of re-presentation, etc. | Drafting of a part diagram (lids and so on). | 200minutes |
| Total. | - | - | 2800minutes |
| Report | Assembly drawing | Parts diagram | Total. | |
|---|---|---|---|---|
| 1. | 3% | 3% | ||
| 2. | 17% | 17% | ||
| 3. | 80% | 80% | ||
| Total. | 3% | 17% | 80% | - |
Students are required to check the report, assembly drawings, parts diagrams from teachers in charge.
Evaluation is carried out according to the evaluation items described in the distributed print, and 60% or more of each is evaluated as acceptable.
Evaluation is carried out according to the evaluation items described in the distributed print, and 60% or more of each is evaluated as acceptable.
Physics 1, Physics 2, Machine material, Mechanism, Strength of materials, Engineering drawing method, Processing engineering.
- Course that cultivates an ability for utilizing knowledge
- Course that cultivates a basic problem-solving skills
| Work experience | Work experience and relevance to the course content if applicatable |
|---|---|
| Applicatable | Two teachers with practical experience at a car maker teaches the basics of mechanical design based on R & D experience in mechanical systems. |
Last modified : Thu Mar 21 14:54:17 JST 2019