Course title
F08467002
Basic Experiments on Information and Communication Engineering C

 saitoh atsushi Click to show questionnaire result at 2019

kanzawa yuuchi

kubota shuji

shindo takuya
Course description
This course includes the following contents:

[Hardware Course]
- hardware design, making and test of operation, especially logic circuit.
- usage logic ICs

* This class is conducted in parallel with software programing 3.
Students of this class and software programing 3 are divided into two groups and replaced after 7th week.
Purpose of class
[Hardware Course]
The aim of this course is
- Learning how to design of logic circuits
- Learning how to use logic IC

[Computer Programming]
Students will develop skills in designing and writing simple computer programs in C programming language.
Goals and objectives
  1. [Hardware Course]
    Understanding circuit diagram and making the circuit
  2. [Hardware Course]
    Understanding combinational circuit and sequential circuit
  3. [Hardware Course]
    Understanding advantage and disadvantage of digital circuit
  4. [Computer Programming]
    Students can understand the concept of "address" in C programming language.
  5. [Computer Programming]
    Students can understand how to manipulate pointers in C programming language.
    Students can understand how strings are represented in C programming language, and how to perform string operations.
Language
Japanese
Class schedule

 Class schedule HW assignments (Including preparation and review of the class.) Amount of Time Required
1. Guidance
・about contents of this course 		Review the contents of Basic Experiments on Information and Communication Engineering C before the class participation 90minutes
Communicate with your group members 10minutes
2. [Hardware Course]
Fundamentals of logic circuit
− Design of LED circuit
− About logic ICs and its usage 		Reading 2nd week's material. 90minutes
Summarize measured data 90minutes
3. [Hardware Course]
Preparation of signal source for experiments
- About usage counter IC
- Check the operation of gate ICs using counter IC
- Preparation of design combinational circuit 		Reading 3rd week's material. 90minutes
Summarize measured data 90minutes
4. [Hardware Course]
Design, making and experiment of combinational circuit
- majority decision circuit
- Full adder
- 2 to 1 selector 		Reading 4th week's material. 90minutes
Summarize measured data 90minutes
5. [Hardware Course]
Preparation and design of sequential circuits
- About Flip-Flop
- About design technique of sequential circuits
- Design of counter circuits 		Reading 5th week's material. 90minutes
Summarize measured data 90minutes
6. [Hardware Course]
Making and experiment of sequential circuits 		Reading 6th week's material. 90minutes
Summarized measured data 90minutes
7. [Hardware Course]
Exam
- Design and making application circuit of sequential circuit 		Review the contents of 1st - 6th week class. 120minutes
8. [Computer Programming]
Introduction.
Pointer 		Reviewing pointer 190minutes
9. [Computer Programming]
Relation between arrays and addresses 		Reviewing relations between arrays and addresses 190minutes
10. [Computer Programming]
Passing parameters by reference 		Reviewing passing parameters by reference 190minutes
11. [Computer Programming]
Passing arrays 		Reviewing passing arrays 190minutes
12. [Computer Programming]
String 		Reviewing string 190minutes
13. [Computer Programming]
Dynamic allocation 		Reviewing dynamic allocation 190minutes
14. [Computer Programming]
Term-end examination and review 		Preparing term-end examination 190minutes
15. − −
Total. - - 2450minutes
Relationship between 'Goals and Objectives' and 'Course Outcomes'

 [Hardware Course] Short report [Hardware Course] Final report [Computer Programming] Reports [Computer Programming] Exam. Total.
1. 10% 10%
2. 15% 10% 25%
3. 5% 10% 15%
4. 5% 12% 17%
5. 10% 23% 33%
Total. 30% 20% 15% 35% -
Evaluation method and criteria
More than 2 times of absence regards as course abandonment.
And, late arraivals to class without just cause is treated as penalty point.

[Hardware Course]
Evaluation depends on 4 reports (30%) and final report (20%) on last class.

[Computer Programming]
Report (15%) and term-end examination (35%).
Textbooks and reference materials
[Hardware Course]
Textbook :
Handouts of this course

Reference materials :
There are many references about logic circuit design. You should choose books suitable for yourself.

[Computer Programming]
recommended through class
Prerequisites
[Hardware Course]
- Read handouts before class participation.
- Squared paper is required.

[Computer Programming]
Grade B or greater in the subject "Basic Experiments onInformation andCommunication Engineering B", or equivalent skill
Office hours and How to contact professors for questions
  • [Hardware Course]
    Before and after class.
    By e-mail (saitoa@sic.shibaura-it.ac.jp)
  • [Computer Programming]
    Before and after classes.
    The lecturer recommends making appointment in advance.
Regionally-oriented
Non-regionally-oriented course
Development of social and professional independence
  • Course that cultivates an ability for utilizing knowledge
  • Course that cultivates a basic interpersonal skills
Active-learning course
About half of the classes are interactive
Course by professor with work experience
Work experience Work experience and relevance to the course content if applicable
N/A N/A
Education related SDGs:the Sustainable Development Goals
  • 9.INDUSTRY, INNOVATION AND INFRASTRUCTURE
Last modified : Sun Mar 21 15:13:06 JST 2021