Exercise of Basic Drawing

Course title

Y0213300

Course description

In the basic drafting exercise, you will acquire the basics of the ability to read and create drawings necessary for the designer. First, you will learn the basics and composition of drawings, and then you will learn about dimensioning methods, fittings, tolerances, materials, welding methods and their symbols. Acquire the basic knowledge through the practice of drafting each time. In addition, learn how to draw machine elements such as screws and flanges that are frequently used as machine parts. You basically use AutoCAD and aim to acquire mechanical design skills.

Purpose of class

Learn the procedure and method of mechanical drawing based on JIS. Learn about mechanical drawing with AutoCAD.

Goals and objectives

You can imagine a three-dimensional figure by looking at a two-dimensional figure. You can understand the projection method.
You can understand dimensioning methods, tolerances, and fits.
You can create drawings. You can use AutoCAD.

Language

Japanese

Class schedule

	Class schedule	HW assignments (Including preparation and review of the class.)	Amount of Time Required
1.	Class guidance Lecture: Structure of drawings Exercise 01: V-block packing retainer	Check the contents of the lesson	120minutes
2.	Lecture: Dimensioning Exercise 02: Mawashigane and eyebolts	Check the contents of the lesson, Submission of exercises	120minutes
3.	Lectures: drawing scale Exercise 03: Toskan	Check the contents of the lesson, Submission of exercises	120minutes
4.	Lecture: Types of drawings Exercise 04: Mini Jack	Check the contents of the lesson, Submission of exercises	120minutes
5.	Lecture: screw drafting Exercise 05: Bolts and nuts	Check the contents of the lesson, Submission of exercises	120minutes
6.	Lecture: Tolerance and Fit (Dimensional Tolerance) Exercise 06: Spanner	Check the contents of the lesson, Submission of exercises	120minutes
7.	Lecture: Gears Exercise 07: Gears	Check the contents of the lesson, Submission of exercises	120minutes
8.	Lecture: material symbol Exercise 08: Handle car	Check the contents of the lesson, Submission of exercises	120minutes
9.	Lecture: surface texture Exercise 09: Bearings with bushings	Check the contents of the lesson, Submission of exercises	120minutes
10.	Lecture: Welding symbols Exercise 10: Air Tank	Check the contents of the lesson, Submission of drawings	120minutes
11.	Lecture: Omitting Figures, Sectional Views Exercise 11: Flanged flexible shaft coupling	Check the contents of the lesson, Submission of drawings	120minutes
12.	Lecture: Tolerance and Fit (Geometric Tolerance) Exercise 12: Gear pump	Check the contents of the lesson, Submission of drawings	120minutes
13.	Lecture: General review Exercise 12: Gear pump	Check the contents of the lesson, Submission of drawings	120minutes
14.	Final exam	Total review of all learning content	120minutes
Total.	-	-	1680minutes

Relationship between 'Goals and Objectives' and 'Course Outcomes'

	Drawings	Final exam	Total.
1.	25%	8%	33%
2.	25%	8%	33%
3.	25%	9%	34%
Total.	75%	25%	-

Evaluation method and criteria

Drawings (submitted materials: mechanical drawings to be performed each time) and the final exam are evaluated, and a score of 60 or higher is considered a pass. The guideline for 60 points is to be able to draw machine drawings that can be interpreted by AutoCAD. The evaluation of assignments is based on a maximum score of 5 points for exercise 01 to 04, and 10 points for subsequent tasks, and the total score is multiplied by 0.75. The score for the final exam will be the score multiplied by 0.25.

Feedback on exams, assignments, etc.

ways of feedback	specific contents about "Other"
Feedback in the class	毎回の課題は次の授業前までに提出する．その後，無作為に受講生に配布し，間違い箇所のチェックを行う．

Textbooks and reference materials

Distribute the textbooks needed in class.
はじめてでもよくわかる図面の描き方，飯島晃良，成美堂出版
新編JIS機械製図、吉澤武男、森北出版

Prerequisites

Install AutoCAD on your own computer
Learn AutoCAD to a level where you can draw simple drawings
It is desirable to take production processing studies

Office hours and How to contact professors for questions

E-mail, Q & A when in the room (appointment required)

Regionally-oriented

Non-regionally-oriented course

Development of social and professional independence

Course that cultivates an ability for utilizing knowledge

Active-learning course

Most classes are interactive

Course by professor with work experience

Work experience	Work experience and relevance to the course content if applicable
Applicable

Education related SDGs:the Sustainable Development Goals

9.INDUSTRY, INNOVATION AND INFRASTRUCTURE

Last modified : Sat Sep 09 05:57:43 JST 2023